インテルのみ表示可能 — GUID: ybd1507803113452
Ixiasoft
インテルのみ表示可能 — GUID: ybd1507803113452
Ixiasoft
4.3.16. FIFO Intel® FPGA IP のパラメーター
パラメーター | 選択可能な値 | 詳細 | ||
---|---|---|---|---|
パラメーター設定: Widths, Clk, Synchronization | ||||
How wide should the FIFO be? | — | データポートと q ポートの幅を指定します。 | ||
How deep should the FIFO be? Note: You could enter arbitrary values for width | 4、8、16、32、64、128、256、512、1024、2048、4096、8192、16384、32768、65536、131072 | FIFO の深度を指定します。これは常に 2 の累乗です。 | ||
Do you want a common clock for reading and writing the FIFO? |
|
— | ||
パラメーター設定: SCFIFO Options | ||||
Would you like to disable any circuitry protection?
|
On/Off | — | ||
パラメーター設定: DCFIFO 1 | ||||
No, synchronize reading and writing to 'rdclk' and 'wrclk', respectively. Create a set of full/empty control signals for for each clock. を選択している場合は、次のオプションが利用可能です。 合計レイテンシー、クロック同期、準安定状態の保護、エリア、fmax のオプションはグループとして設定する必要があります。合計レイテンシーは、書き込みクロックの 2 つの立ち上がりエッジと以下で選択されている読み出しクロックの数の合計です。 Which option(s) is most important to the DCFIFO? (Read clk sync stages, metastability protection, area, fmax) Which type of optimization do you want? |
|
合計レイテンシー、クロック同期、準安定状態の保護、エリア、fmax を指定します。
|
||
More Options | Best metastability protection, best fmax, unsynchronized clock を選択している場合は、次のオプションが利用可能です。
|
3、4、5、6、7、8、9 | 同期ステージの数を指定します。 | |
Timing Constraint
|
On/Off | SDC ファイルを正しいタイミング制約で生成します。組み込まれている set_false_path 割り当ては無効になります。新しいタイミング制約は、set_net_delay、set_max_skew、set_min_delay、set_max_delay で構成されます。タイミング制約の使用方法に関しては、ユーザーガイドを参照してください。 | ||
パラメーター設定: DCFIFO 2 | ||||
No, synchronize reading and writing to 'rdclk' and 'wrclk', respectively. Create a set of full/empty control signals for for each clock. を選択している場合は、次のオプションが利用可能です。 Which optional output control signals do you want? usedw[] は、FIFO のワード数です。 |
On/Off | — | ||
読み出し側
注意: これらの信号は、「rdclk」に同期しています。 |
— | |||
書き込み側
注意: これらの信号は、「wrclk」に同期しています。 |
— | |||
More Options |
|
On/Off | — | |
パラメーター設定: Rdreq Option, Blk Type | ||||
Which kind of read access do you want with the rdreq signal? |
|
FIFO をレガシーモードにするか、Show-ahead モードにするかを指定します。
|
||
What should the memory block type be |
|
メモリーブロックのタイプを指定します。選択可能なメモリーブロックのタイプは、ターゲットデバイスによって異なります。 | ||
Set the maximum block depth to | Auto、32、64、128、256、512、1024、2048、4096、8192、16384、32768、65536、131072 | 最大ブロック深度をワード数で指定します。 | ||
Reduce RAM usage (decreases speed and increases number of Les). Available if data width is divisible by 9. | On/Off | — | ||
パラメーター設定: Optimization, Circuitry Protection | ||||
Would you like to register the output to maximize the performance but use more area? |
|
RAM の出力をレジスターするかを指定します。 | ||
Implement FIFO storage with logic cells only, even if the device contains memory blocks. | On/Off | ロジックセルのみで FIFO ストレージを実装するかを指定します。 | ||
Would you like to disable any circuitry protection (overflow checking and underflow checking)?
If not required, overflow and underflow checking can be disabled to improve performance.
|
On/Off | オーバーフローに対する回路保護を無効にするかを指定します。 | ||
Would you like to enable ECC?
|
On/Off | エラーの検出と訂正機能を有効にするかを指定します。 |